The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.
| Author: | Maugami Zulura |
| Country: | Kuwait |
| Language: | English (Spanish) |
| Genre: | Finance |
| Published (Last): | 16 July 2009 |
| Pages: | 355 |
| PDF File Size: | 19.47 Mb |
| ePub File Size: | 16.63 Mb |
| ISBN: | 587-1-62673-893-3 |
| Downloads: | 14988 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Zulkikus |
Factory setting depends on Control Method A Factory setting differs depending on drive capacity. XX A If no problems are encountered, the following message will appear: The input commands at terminals 3 magetek 8 are a combination of 1’s and 0’s, which are received as an on or off condition at each terminal.
Consult Yaskawa when connecting noise filters to the drive output. After the number of pulses have been completed, the multi-function output changes to magnetei open OFF state. The time should be adjusted so that this minimal error is attained as fast as possible, without making the system oscillate.
IMPORTANT. Engineering Bulletin # Magnetek GPD Start Up and Adjustment Guide – PDF
Droop Control Gain Factory setting: Watch list is full. Calculate Varies based on location and shipping method. Press the key once. After any parameters have been programmed, the “User Program” option appears in the choice of Access Levels. On the larger drives with sheet metal chassis, it may be mounted inside the area where the input power wiring enters the drive.
Digital Operator Table When it comes to GPD repair facilities, PES stands above the rest with our years of training and service history for this product line. A Cheat Sheet Open Loop Vector The following procedure is a supplement to supplied with this equipment magneek will guide the user in properly wiring the A and. VFD Lesson 4. The turn around time for the repaire I sent in was very good. Consult factory for derating of larger drives.
GPDG5-Installation | Yaskawa MagneTek Troubleshooting by Yaskawa | MRO Electric
magnete, A Output Frequency Max. Press the ESC key. A Motor overload Protects the motor. Press RUN light remains on. BCD 1 Hz 7: Factory setting differs depending on the control method A 1 – 0 2. Frequency reference no longer acts as PID setpoint. Use the and keys to scroll through the Functions and Parameters. Communication option card failure.
A Selection for OL Protection Base Frequency E 1 – 0 7: Please enter a number less than or equal to 1. It should be decreased for a vibrating condition under heavy loads, and increased for hunting under light loads.
Yaskawa / Magnetek GPD 515/G5 Sine-Coded Pulse Width Modulated AC Motor Drive
Speed Coincidence Detection Level Factory setting: Dynamic braking DB enables the motor to be brought to a smooth and rapid stop. The drive will be in torque control when the corresponding input terminal is closed. Detected during running, and operation continues after detection 3: Feedback loss detection is enabled – fault drive coasts to stop b 5 – 1 3: We received great service, as we purchased one part and it arrived incorrect, so the service to fpd us the correct part was great, also arranged to ship back the incorrect one.
Connect only the number of braking transistor units and remote mount resistor units required for the application. For information on other types of enclosures available, consult your Magnetekk representative. This feature can be selected to operate over a wide range of conditions. Verify that the rated voltage of the drive matches the voltage of the incoming power. Alpi 6 – zona industriale – Lonato BS Tel.
GPD515C-B034
The o 1 – 0 1 parameter corresponds to the o 1 gp 0 2 setting “4 – Selected Monitor”. Remove power, remove the old control board, and install the new control board. A Main contactor fault Main circuit magnetic contactor soft charge contactor does not operate correctly. The master communicates with one slave at a time.
The effective DC injection time and current should be set to provide adequate stopping without magneek motor heating. Connect drive ground terminal or panel to earth ground.