Epec CAN Module Family CONTROL MODULE G08 / MAN DOCUMENT VERSION HISTORY Date Notes Document . Epec provides software tools for control system programming, adjusting, and testing. From the systems engineering viewpoint, it is not enough to have sufficient. Open and compatible. Embedded control systems are based on PLCopen and CANopen®, which make them easily scalable to meet requirements for both.

Author: Mekora Zunos
Country: Colombia
Language: English (Spanish)
Genre: Education
Published (Last): 22 July 2016
Pages: 481
PDF File Size: 5.35 Mb
ePub File Size: 3.71 Mb
ISBN: 185-1-68786-820-1
Downloads: 50261
Price: Free* [*Free Regsitration Required]
Uploader: Tonos

These kinds of pins have a small shunt resistor connected to ground. The first is one of the QX output bits for controlling the pin as an output. The application program will see there a logical zero when the pin is grounded or left open and a logical one when the pin is connected to a positive voltage source. Additional module cover for wires and connectors is also available E 6. In PLCopen programming environment, there is a word variable in IW area associated with each pin from where the software can read the actual signal magnitude at the pin.

For example, if group two is configured as a current input, then both pins X3.

Open loads can not be detected because the internal load resistor is connected to the ground. Operating range 10…30 VDC? The shutdown circuit cuts off the power feed for the logic and loads in case of overvoltage. The maximum rating is lowered in this case to 15 volts.

They can be used as high impedance voltage inputs for signals from 0 to 5 volts or low impedance current inputs for signals from 0 to 22,7 milliamperes.

EPEC 数据手册新版_图文_百度文库

The warranty does not cover possible expenses relating to travelling, accommodation, daily benefits, etc. Box FIN Sein? No scrapping fee will, however, be charged for products that are received by the manufacturer during the warranty period.


So, the practical limits are lower but the maximum values of the table still give the basis for the estimation.

Bram Engineers De kracht van Mechatronics!

The pulse counting competes with the application program and other processes for the CPU time. Recommended operating voltage 24 VDC? Weight 0,7 kg Applications? We believe that we know control systems for challenging conditions and we are able to offer a total eped from control eepc to project services and designing. A separate safety analysis is always recommended for the machine and its control system. CAN2 is user programmable? All cables, connectors and tools must be of correct type and sufficiently high quality.

Violating this rating may lead to application program not noticing all input state transitions Epec Oy epef all rights for improvements without prior notice Epec Oy Matinkatu 6 FIN Sein? Operating voltage 10 – 30 VDC? Inputs are divided into groups by the input impedance configuration. Generally, it is not recommended.

The Mini module and the Mini display need the Hub module in order to have the full transient immunity. If separate Epec module shock protection cover E is mounted, it is recommended to use Epec E fastening bolts? Power feed is restored when supply voltage drops to 30 V. The first is a bit variable in the IX area just in the same way as with the pins without the PI features. A small and protective module casing keeps inside high performance microcontroller with lots of control capabilities.

The buyer shall attach to the claim a possible error report or equivalent explanation of the grounds for the claim.

  LEY 20488 PDF

It must be taken care in system design that the output unintentionally switching to on state causes no harm to the system.

With input voltages below 4,3 V it seems like the internal input resistance was connected to a 1,3 V voltage source Note 2: Test method EN ?

2pcs EPEC 2024 ECU Plug 35 Car Waterproof Connector 776273 – 1 770680 – 1 and Termina

In high impedance voltage input configuration they have low threshold voltage which is quite sensitive to interference signals. The Color display needs extra facilities in order to have the limit B covered. Violating this rating may lead to system not recognizing all input state transitions Note 4: In those cases, the output functionality of the pin must of course be kept in epc state. In other words, pins connect the load to the ground. The second is one of the IX input bits for monitoring the actual state of the output or reading the pin as an input.

In carefully selected applications these pins can also be used as digital inputs. The pairing is done in application program.

Module has a shutdown circuit which protects the module and loads against overvoltage. The application program can also simultaneously monitor the actual state of the pin. The peec does not cover any costs related to removing or fastening of devices related to the products.

The other two are word variables in the IW memory area which hold the frequency value and the number of pulses.