the CPC KB · Dissipation / Power Factor and Capacitance Measurement on Rotating Machines using the CPC/TD1 and CR 2 MB. OMICRON. CPC Reference Manual. PRIMARY TEST SYSTEM. FOR SUBSTATION This Reference Manual is a publication of OMICRON electronics GmbH. All rights . View and Download Omicron CPC user manual online. CPC Test Equipment pdf manual download.
| Author: | Nikoshura Vujas |
| Country: | Luxembourg |
| Language: | English (Spanish) |
| Genre: | Video |
| Published (Last): | 28 March 2017 |
| Pages: | 372 |
| PDF File Size: | 3.73 Mb |
| ePub File Size: | 10.7 Mb |
| ISBN: | 828-4-62060-844-9 |
| Downloads: | 14070 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Mizshura |
Once these phrases are saved, they can then be selected as template phrases from the Select a phrase combo box. The CPC V1 allows using more test cards in one test procedure but we recommend not to use more than 15 test cards to keep the tests clearly structured.
Line impedance omicrkn k-factor Calculating impedances and the k-factor is highly errorprone. A series of three ramps defined in the ramps table Ramp 1 Ramp 2 Ramp 3 The three ramps defined in the ramps table shown above result in an output signal like this: If not included, it needs to be purchased separately.
This signal can either be a voltage or a current signal from CPCand has a signal characteristic similar to a saw-tooth signal with a different steepness for the rising and the falling slope. Thus the correct VT polarity can be verified.
The Frequency-selective Measurement The Frequency-Selective Measurement The frequency-selective measurement is used to filter out interferences as they usually occur in substations.
Signals below 45 Hz with reduced values possible.
Related Searches Power transformer Industrial calibrator Test set stand Measuring system Laboratory mamual Electrical network analyzer Manual calibration system Circuit breaker test device PTP clock Power quality analyzer Relay test Multi-parameter analyzer Automatic test device Industrial transformer Communication network analyzer Precision test device Programmable converter Dielectric response analyzer Computer-controlled analyzer PTP converter.
These settings affect the way the CPC software displays and sort dates, times, numbers and decimal points.
OMICRON CPC USER MANUAL Pdf Download.
Page 28 CPC V1. Transformer After then, pressing the A menu key repeatedly adds more taps with a step calculated from the values omkcron the first two taps. Sequencer test card with parameters and measurements of the five states states ommicron To do so, Janual injects a special polarity test signal at a certain location. Rground Smaller grounding systems with a diameter of m ft or smaller can be tested with the RGround test card and CPC alone, for large systems the CP CU1 coupling unit and the Sequencer test card is a better choice.
Page Figure 4 above it is the output current. Page CB opens again ms ms state 1 state 2 state 3 state omifron short long dead time dead time State 2 and 4 incl. Introduction Disable ground check Operating CPC with the “Disable ground check” check box selected can cause injury or possibly death of the operating staff if the power supply is not metallically separated and the PE protective connection is defective. Example of a list box List boxes are differentiated between read-only and editable list boxes: It The following table shows the V prim and V sec settings on the TRRatio test card for different automatically fills in the nominal ratio table of the TRRatio test card for symmetric tap changers.
Omicron CPC 100 User Manual
The possible entry range from … allows the first digit to be used as a phase identifier. The focus is set onto the “I test: Any translation of this manual is done for local requirements, and in the.
Page 40 Socket to omifron an external booster, for example, the CP CB2 current booster for output currents of up to A. A manula represents an output quantity with defined settings, for example, a certain magnitude and frequency, for a preset period of time. Solder each wire to its corresponding contact of the insert.
Contents of this section Test Assessment Substation A ground Substation B ground You can use existing power cables. Smaller grounding systems with a diameter of m ft or smaller can be tested with the RGround test card and CPC alone, for large systems the CP CU1 coupling unit and the Sequencer test card is a better choice.
Socket to connect an external booster, for example, the CP CB2 current booster for output currents of up to A. CB opens again ms ms state 1 state 2 state 3 state 4 short long dead time dead time State 2 and 4 incl. Then press the handwheel.
In particular, avoid disruptions that could in turn affect safety. To avoid saturation, sudden magnitude changes are suppressed. Far end Far end CPC — The revolutionary all-in-one test system The patented test system replaces numerous individual testing devices and offers new, innovative testing methods.
Do not connect the 2kV output to this input!