THERMAL INSULATION OF PIPING. (WITH AMENDMENTS / SUPPLEMENTS. TO THE CINI HANDBOOK). Document nr.: PIP – This specification has. atta&ible with thermal insulation in building wall and piping . This handbook of thermal insulation applications vas prepared by EM4C. ducts and steam pipe systems with operating temperatures that are constantly above °C. CINI Manual “Insulation for industries”. CINI recommends applying .
|Published (Last):||17 November 2007|
|PDF File Size:||5.88 Mb|
|ePub File Size:||9.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
Valves and flanges in piping shall be provided with removable insulation covers. The placing of the pre-formed spacers will depend on the location of supports, welds, auxiliaries, etc.
Alternatively, mattresses may fit in complicated configurations, but water ingress shall be avoided. Dip tank operations involving flammable More information.
TICP and shall be subject to the approval of the Principal. Inzulation radiation shall be taken into account.
Subject to any particular terms and conditions as may be set forth in specific agreements with users, Shell GSI, SIEP and SIC disclaim any liability of whatsoever nature for any damage including injury or death suffered by any company or person whomsoever as a result of or in connection with the use, application or implementation of any DEP, combination of DEPs or any part thereof, even if it is wholly or partly caused by negligence on the part of Shell GSI, SIEP or other Service Company.
Air-Conditioning, Heating, and Refrigeration Institute.
CINI revises its insulation manual and includes ULTIMATE
Stilling Well Recommendations White Paper June 24, Stilling Well Recommendations This document describes general requirements for stilling wells used for radar tank gauging applications. Drawings and general provisions of the Contract.
Insulation adjacent to flanges in piping and equipment shall be terminated to allow removal of bolts without damage to that insulation. These specifications may be used in whole or in part by any party without More information.
The rate of condensation depends on ambient temperature, relative humidity, and emissivity of bare surface or insulation jacketing, wind velocity and process temperature Corrosion Under Insulation. Tentative sizes must be allocated to each structural.
Dip tank operations involving flammable. The jacketing selection has been changed.
The heat gain heat ingress for piping in off-plot areas shall be determined by the Principal. Joints and ends shall be taped with self-adhesive aluminium tape. Without prejudice to any specific terms in respect of confidentiality under relevant contractual arrangements, DEPs shall not, without the prior written consent of Shell GSI and SIEP, be disclosed by users to any company or person whomsoever and the DEPs shall be used exclusively for the purpose for which they have been provided to the user.
Insulatikn phenomenon of CUI is often underestimated, as it will occur years after completion of a insulagion.
CINI revises its insulation manual and includes ULTIMATE
The adhesives shall withstand any stresses and strains, accommodate contraction within the foam and remain effective within the required temperature range. The Insulation Contractor is the party that carries out the insulation works, including engineering, material supply, installation and quality control. Between the acoustic insulation and the jacketing a vapour barrier shall be provided that includes a heavy duty multiplex foil, covered insuation a UV curable GRP.
Spacers shall be fastened securely by means of stainless steel bands, filament tape or glue. The Principal may sometimes undertake all or part of hwndbook duties of the Main Contractor. Method c is normally used for tank walls ref. The systems and materials shall perform as well as or better than the preferred system and material. If metal jacketing is used, sufficient handbok and drainage shall be provided to avoid internal accumulation of water caused by condensation, water vapour diffusion, capillary action and water ingress.
The method for calculating the economic thickness of insulation shall be in accordance with Section 1. LNG loading lines Injection Application methods a and b The foam injection process shall be in accordance with the recommendations of the Manufacturer.
Tentative sizes must be allocated to each structural More information.
THERMAL INSULATION (AMENDMENTS/SUPPLEMENTS TO THE CINI HANDBOOK)
The following table indicates vulnerabilities to CUI: Service loads shall include thermal stresses resulting from differential contraction of the foam and the pipe, thermal stresses resulting from the temperature gradient through the thickness of the insulation, clamping forces, mechanical loads applied by the piping system and any other loading that may be present at the support. The emissivity of these materials is typically 0. All of these questions will be answered.
Where multi-layering is necessary, longitudinal and circumferential joints shall all be staggered. Pouring shall only be allowed for emergency maintenance, if injection equipment is not directly available. This standard is intended to provide useful information to the Professional Service Provider PSP to establish a basis of design.
Furthermore, if for process reasons the allowable temperature drop is limited, e. This is of particular importance where DEPs may not cover every requirement or diversity of condition at each locality.
VdS Guidelines for water extinguishing systems. Pipes laid in the ground must be introduced into concrete walls or shafts. White Paper June 24, Stilling Well Recommendations This document describes general requirements for stilling wells used for radar tank gauging applications. Lochinvar Lock-Temp Tanks have been specifically designed and engineered to provide a. Part VI contains appendices with diagrams, tables and drawings.