CINETECH KNP PDF

KNP Web 15,, views · · Colors for Children to Learn With Street Vehicles and Water Slide – Colours Magic Liquids For Kids BinBin. CINETECH > Hard to find / Shortage Pricing, Availability, Datasheet Download, and Product CRJT, CINETECH KNPWJ0R1, CINETECH. Taiwan Wirewound Resistors SQP, KNP is supplied by ☆ Wirewound Resistors Cinetech Ind Co Ltd does not currently advertise comprehensive company.

Author: Faulabar Zologami
Country: El Salvador
Language: English (Spanish)
Genre: Marketing
Published (Last): 9 February 2010
Pages: 364
PDF File Size: 2.83 Mb
ePub File Size: 7.74 Mb
ISBN: 546-8-83879-308-5
Downloads: 91923
Price: Free* [*Free Regsitration Required]
Uploader: Gujar

Hosonic Electronic Hosonic Electronic. Maxim Integrated Maxim Integrated.

Cinetech – Computer and PC Parts Catalog

Micross Components Micross Components. Step 3 Suck any extra solder that is left between the pads and the part.

See datasheet for details. Crystek Corporation Crystek Corporation. Two pin SMD component, such as a chip capacitor or resistor, is the easiest to de-solder with a regular soldering iron tip. Mount the circuit board in a vise that will not burn when heated. Use needle-nose pliers to hold the part in place while heating. Fox Electronics Fox Electronics. Step 1 Place a small amount of solder on one of the conner pads. Step 2 Heat one side and move the iron back and forth until the whole row of pins is melted.

Up to 10WResistance Range: General Electric General Electric.

best smd metal foil list

Step 1 Place a small amount of solder on one of the three pads. Blow on cineech part to harden the solder. International Semiconductor International Semiconductor.

  KIRITH KIRIN PDF

Heat the pad with solder and adjust the part so that it lines up with the pads. American Microsemiconductor American Microsemiconductor. Cinettech Cambion CA Diodes, Capacitors and Resistors in sizes like,,and Inspect around the edges of the part for solder bridges from pad to pad.

Please visit Introduction to soldering in general, if you have never soldered before. Taitron Components Taitron Components.

Semicoa Semiconductors Semicoa Semiconductors. Besure the part is flat and aligned on all four sides, then remove the heat. Pico Electronics Pico Electronics These ultra-precision resistors are based on the planar construction of a cold-rolled Ni-Cr foil bonded to a flat ceramic substrate. Our standard resistors are available variety of models to fit a wide range of applications.

Rhombus Rhombus L L Desoldering SMD Special methods for desoldering without the need for special soldering iron tips. Voltage Multipliers Voltage Multipliers.

3D Glasses – Polarizing

Simply heat one side until the solder is melted, then quickly move to the other side until the solder is melted. The following instructions are for a heat gun only.

Step 4 Using the iron, or a heated sucker heat an end of a row until the solder is melted pins in length from the end. Transys Electronics Transys Electronics.

Insert the screwdriver under that side and pry up until the pins are off the PCB and out of the solder. The guide is organized into different methods. Heat the pad already with solder and slide the part onto the pad so that it is centered between the three pads. A properly soldered joint should have a curved line from the end of the pad to the top of the part as shown in the pictures.

  ENVY 15-3090LA PDF

Step 2 Grab the 8 pin SOP part with very fine tweezers. World Products World Products. Try to keep the solder across the pins as even as possible.

Besure the part is flat and aligned, then remove the heat. Finally inspect the pins to check if any solder is left between them. Cinetecu the pad already with solder and slide the part onto the pad so that it is centered between the pads. This method works because sucking only removes the solder between the pins and not the solder between the pad and pin.

Harris Corporation Harris Corporation. Small Outline Package – SO.

Cinetech Computer Hardware Part Catalog

Do not use the end of the tip or solder will flow from pin to pin. Step 2 Grab the 14 pin SOP part with very fine tweezers. The amount is learned by trail and error and experience.