Atmel AT91SAM7X-EK Manual Online: Errata. E–ATARM–Mar Motherboard Atmel AT91SAMEK User Manual. (39 pages). Motherboard. 7: Only available on products with embedded Flash. 8, 10, 16, 17, 19, 20, 21, On board DataFlash chip. 9: Please check at91sam errata # Example: To compile a DataFlash boot project for AT91SAMEK board, type the following commands: 3: Please check at91sam errata #

Author: Kajibei Kinos
Country: Morocco
Language: English (Spanish)
Genre: Video
Published (Last): 3 May 2015
Pages: 298
PDF File Size: 19.38 Mb
ePub File Size: 9.66 Mb
ISBN: 842-2-42805-501-2
Downloads: 29505
Price: Free* [*Free Regsitration Required]
Uploader: Akiramar

External reset pushbutton 3. Only available on products with embedded Flash 241011131415 Supported on SAM rev B onwards One yellow power LED can be also software controlled 3.

To use the software shutdown control, J3 must be opened. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. DC power is supplied to the board via the 2. Choose the proper media tab DataFlash, NandFlash, etrata.

All material on this collaboration platform is the property of the contributing authors.

A grounding strap or similar protective device should be worn when handling the board. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Power supply and audio! A GND Test point.

  CCN 3196 PDF


Board Layout – Top View! You can find a valuable summary in the document named SAM9 Boot Strategies or see the cross matrix below. Added new schematics in Section 5. To use this feature, the user has to open the strap and insert an anmeter. For more information on this topic, please check the corresponding SAM product datasheet section Boot Program.

In this case, J10 configuration must be set in position 1, 2. Jumpers Configuration Designation Note: Atmel does not make any commitment to update the information contained herein.

Avoid touching the component pins or any other metallic element. Other terms and product names may be trademarks of others. Internal RC Oscillator Usually cross-compiler-prefix- looks like arm-linux- or arm-elf- Notes 1: These jumpers are provided for power consumption measurement use.

Supported on SAM rev B onwards 7: The information in this document is provided in connection with Atmel products. Reproduction and publication without our written authorization shall expose offender to legal proceedings.

No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. Newer version of AT91Bootstrap from version 1. Other terms and product names may be trademarks of others. Added errata Section 6. Printed on recycled paper. Dataflash memories have page size of bytes, 0x hex and the load address 0x is thus in the middle of a page.


AT73C clocking In the present schematics block diagram p. Internal reset controller with bi-directional reset pin!

Connect to LinksToCommunities page. On J10 pin 1 square pin: If S3 is closed, R13 must be unsoldered. Please check at91sam errata Only one available with the lead PQFP package. Removable DataFlash card 89: Lithium 3V Battery Refer to Section 4. The markings for BB and 1V8 are inverted. In the linux4SAM pre-built demo it is used at91sma9260 configure the hardware and to load and start the standard U-Boot bootloader, it can also be configured to start directly the linux kernel.

Two user input pushbuttons 2!

The marking should be: By default, they are closed. Document Comments A First issue. Not available with the lead PQFP package.

LegacyAT91Bootstrap < Linux4SAM < TWiki

Coaxial plug center positive standard. One user green LED! Added new Section 6, Errata. All EBI Signals of the AT91SAM are routed to extension footprint connectors J25 This allows the developer to check the integrity of the components and to extend the features of the board by adding external hardware components or boards.