Buy ASTM D Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils from SAI Global. GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Consolidated Undrained Triaxial Compression Test for . Consolidated Undrained Triaxial Compression Test for Cohesive Soil.
|Published (Last):||13 December 2017|
|PDF File Size:||13.61 Mb|
|ePub File Size:||11.31 Mb|
|Price:||Free* [*Free Regsitration Required]|
Standard triaxial configuration with external data acquisition can be used for performing additional test such as CBR, Unconfined and CRS, Permeability.
In this test method, the shear characteristics are measured under undrained conditions and is applicable to field conditions where soils that have been fully consolidated under one set of stresses are subjected to a change in stress without time for further consolidation to take place undrained conditionand the field stress conditions are similar to those in the test method. After the density has been determined, the unit weight asgm calculated in SI or inch-pound units, or both.
ASTM D Standard
TRITECH original high-performance load frames for triaxial tests, ideal solution for advanced and research laboratories to perform high quality tests at. Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: It is beyond the scope of this test method to consider significant digits used in analysis methods for engineering design.
EmS technology is environmentally friendly and clean to operate, requiring no compressed air or hydraulic oil. In this standard density is given only in Astj units. A typical Standard triaxial system with analogue measurements includes: All the data acquisition and test management are made in manual mode Power supply is only required for air compressor and for triaxial load frame during failure stage.
Using the pore-water pressure measured during the test, the shear strength determined from this test method can be expressed in terms of effective stress. The shear strength of a saturated soil in triaxial compression depends on the stresses applied, time of consolidation, strain rate, and the stress history experienced by the soil.
Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. Consolidation bench for triaxial d4776 The apparatus has been adtm to reduce the testing time for triaxial tests, where only one compression machine is available.
D767 procedures used do not consider material variation, purpose for obtaining the data, special purpose studies or any consideration of end use. Link to Active This link will always route to the current Active version of the standard.
ASTM D, Test equipment Controls
Maintenance Spares Technical trainings Warranty Academy. Users of this test method are cautioned that compliance with Practice D does not ensure reliable testing. It d47767 excellent reliability, accurate testing and lower maintenance requirements.
Agencies which meet the criteria of Practice D are generally considered capable of competent testing. Note 1—If the strength is required for the case where the soil is r4767 consolidated during testing prior to shear, refer to Test Method D or Test Method D More than system configurations are available depending on type of test, sample size, pressure system. The load frame is built around a robust twin column Specimens are isotropically consolidated and sheared in compression without drainage at a constant rate of axial deformation strain controlled.
Soil mechanics – Triaxial load frames: This implicitly combines two separate systems of units; that is, the absolute system and the gravitational d476. Template for data processing and reporting: TRITECH original high-performance load frames for triaxial tests, ideal solution for advanced and research laboratories that perform high quality tests at high productivity levels.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Standard triaxial configuration with built-in data acquisition can be used for performing additional tests such as CBR, Unconfined and CRS.
A typical standard triaxial system with built-in acquisition measurement includes: The design of the cell ensure vertical alignement of the cell ram by clamping the Perspex wall separately from Data acquisition d477 included in the load frame; four channels are available for load, displacement, pore pressure and volume change.
The precision of this test method is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used.