Find the most up-to-date version of ASTM A at Engineering Standard Specification for Steel Forging Stock. Active Standard ASTM A / AM | Developed by Subcommittee: A Book of Standards Volume: . ASTM A/AM Standard Specification for Steel Forging Stock CONTAINED IN VOL. , Covers cast carbon and alloy steel ingots and strand.
|Published (Last):||14 October 2010|
|PDF File Size:||18.5 Mb|
|ePub File Size:||2.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
Hot working in any but the annealed condition can affect the strength level. The alloy will harden by cold working or by heat treatment — see “Heat Treatment” and “Tempering”. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or asstm to date.
Standard – Standard Specification for Steel Forging Stock ASTM A –
Final products xstm be free of injurious surface imperfections. This abstract is a brief summary of the referenced standard. If you like to setup a quick demo, let us know at support madcad. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Heat and product analyses shall be carried out to evaluate conformance wstm steel specimens to chemical composition requirements.
AISI is a heat treatable, low alloy steel containing nickel, chromium and molybdenum.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Search book title Enter keywords for book title search. This specification covers cast carbon and astmm steel ingots and strand castings, semi-wrought ingots and strand castings, and rolled or forged blooms, billets, and slabs for steel forging stock. This specification covers cast carbon and alloy steel ingots and strand castings, semi-wrought ingots and strand castings, and rolled or forged blooms, billets, and slabs for steel forging stock.
Do NOT temper the alloy if it is in the – ksi strength range as tempering can result in degradation of impact resistance for this level of strength.
Standard Specification for Steel Forging Stock
AISI is considered to be a “through hardening” steel such that large section sizes can still be heat treated to high strength. Register for a trial account. Machining is best done with this alloy in the annealed or normalized and tempered condition.
Remember me for one month. Heat treatment for strengthening is done at F followed by an oil quench. For high strength over ksi the alloy should first s711 normalized at F prior to heat treatment.
From F it may be air cooled. They shall apply only when specified by the purchaser. Heat and product analyses shall be carried out to evaluate conformance of steel specimens to chemical composition requirements.
For strength levels in the – ksi range temper at F. Historical Version s – view previous versions of standard.
Blooms and billets may be square, round, octagonal, or rectangular in section; slabs are rectangular. It sstm informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Combining values from the two systems may result in non-conformance with the standard. Are you sure you want to empty the cart?
For strength in the – ksi range a71 at F. There were no books found for the applied search filters.
Although no invariable rule prevails between the terms blooms and billets, and they are frequently used interchangeably, the following size ashm are in general use. Bend radii should be 3t or greater. If, however, such defects do occur, surface conditioning, cutting, or parting may be performed by scarfing or flame-cutting.
Final aetm shall be free of injurious surface imperfections. It is known for its toughness and capability of developing high strength in the heat treated condition while retaining good fatigue strength. This abstract is a brief summary of the referenced standard. Mean Coeff Thermal Expansion.
ASTM A711 Rods, Application: Manufacturing, Construction, School/College Workshop
Please login to your authorized staff account to use this feature. Distributors will offer small quantity buys while mills will generally only sell large quantities, with delivery times anywhere from 10 astn 50 weeks depending on size and form required This material is stocked primarily in Bar Products by 59 atm but is also available to a lesser extent in Flat Rolled Products, Forging Products, Tubular Products, Wire Products, Fasteners, Piping Components, and Structurals.
The alloy may be cold worked, in the annealed condition, by conventional methods and tooling.