74LS688 DATASHEET PDF

Texas Instruments 74LS Logic Comparators are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments . December INTEGRATED CIRCUITS. 74HC/HCT 8-bit magnitude comparator. For a complete data sheet, please also download. Part Number: 74LS, Maunfacturer: National Semiconductor, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor.

Author: Vogrel Sharr
Country: Great Britain
Language: English (Spanish)
Genre: Literature
Published (Last): 21 December 2005
Pages: 16
PDF File Size: 17.96 Mb
ePub File Size: 4.50 Mb
ISBN: 157-1-33365-468-5
Downloads: 90192
Price: Free* [*Free Regsitration Required]
Uploader: Tejind

A way to avoid that would be to de-glitch the circuit by adding a synchronizing flip-flop running at 16MHz just before the latching flip-flop. You could then use it as a clock.

74LS688 Datasheet PDF

This might cause a false trigger if your address trap was at B. You can’t use datasheett while the inputs are changing. It’s comparing the high four address bits to a 4-position DIP switch.

Just to scratch my own curious itch, what does the connect to? I’m currently designing the power-on-jump circuit for my processor board.

I don’t do well with word descriptions of circuits–can you draw a schematic? I’m not talking about little tiny noise spikes. This sets the D-type flip flop, which switches off the NOP generator and turns on the bus tranceivers.

74LS datasheet,datasheets manu Page:5====[未知厂家] pdf datenblatt – –

Here’s the pieces relevant to Power on Jump: When the system comes up from a reset, a 74LS with its inputs all tied to ground is connected to the data lines of the CPU and the data bus tranceivers are switched off datashete this feeds the CPU NOPs until the address equals what’s set on the DIP switch.

  6ES7314 1AE04 0AB0 PDF

If you expect to use it, datashwet need to turn the enable off during the time when the compare inputs are in transition. It is a glitchy signal. It might work, but I don’t like it much. This would also add about 62 nS to your latch clock which right now is only 3 gate delays long and would be difficult to see on an old low bandwidth scope.

You’re depending too much on the propagation delay of the 74 and the creating a clock pulse of the minimum required width t wclk on your datasheet.

Note that this would take away 62 nS from the access time of the first instruction fetch after the proper address compare, but it should be OK if you are using newer memory devices. As datasheett address lines transition and settle out, they might very well set up a glitch that agrees with the test condition, well before you intended. Hi No it won’t.

74LS Datasheet, PDF – Alldatasheet

Hi I doubt you’ll be able to run the output of the directly to a clock. This is all fine. Any datahseet, like the will create big nasty full swing glitches that can only be removed with the proper clocked gating or latching. In other words, what function does it serve? My calculations say yes, with lots of time to spare, but I’d like others’ opinions.

  LEY 24041 PDF

I’ve never had to use one. I’m not that good with circuit design, but is it possible a monostable multivibrator one-shot would do the datashet

It may even make it worse. I got lost reading that.

74LS688 IC 8-BIT IDENTITY COMPARATOR

Glitchy output shouldn’t be a problem — it needs to be inverted for the D-type flip flop’s clock anyway, so I’m using a 74LS14 inverter, which has Schmitt inputs and should clean up the signal into a nice, sharp positive-going square wave.

There may be better ways to do this job so keep tinkering. Glitchy output shouldn’t be a problem — glitch, I see how you got datashret nickname. It’s an 8-bit comparator, but it’s cheaper than the 74LS85 and has an enable input. For example, going from 9 to A might give a false compare of B for a few nanoseconds.